消費電力の低い2.5inch HDDであるTravelstar 7K1000を購入し、2か月強使用したのですが、故障したためそのsmart値を載せておきます。2台購入して、RAID1で利用していた片方が死んだ形になるので、もう一台も近日中に死ぬような事があればこのHDDは半年以内に2/2の確率で死んだことになってしまうので、そうならない事を祈っています。
HGSTのサポセンに送り返すことになるので、その対処方法等は後でまとめる予定です。
smartctl -a /dev/sdb smartctl 6.2 2013-04-20 r3812 [x86_64-linux-3.11.0-12-generic] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: HGST Travelstar 7K1000 Device Model: HGST HTS721010A9E630 Serial Number: JG40006EG***** LU WWN Device Id: 5 000cca 6a6c1c165 Firmware Version: JB0OA3B0 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Nov 10 11:40:04 2013 JST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 173) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 082 082 062 Pre-fail Always - 28377158 2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0 3 Spin_Up_Time 0x0007 182 182 033 Pre-fail Always - 2 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 63 5 Reallocated_Sector_Ct 0x0033 073 073 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0 9 Power_On_Hours 0x0012 097 097 000 Old_age Always - 1476 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 63 191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 11 193 Load_Cycle_Count 0x0012 099 099 000 Old_age Always - 14390 194 Temperature_Celsius 0x0002 253 253 000 Old_age Always - 20 (Min/Max 16/59) 196 Reallocated_Event_Count 0x0032 064 064 000 Old_age Always - 1033 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 72 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 17 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 17 occurred at disk power-on lifetime: 1476 hours (61 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 28 00 05 40 04 Error: UNC at LBA = 0x04400500 = 71304448 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 28 00 00 05 40 40 00 4d+08:09:51.223 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 4d+08:09:51.221 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 4d+08:09:51.220 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 4d+08:09:51.218 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 4d+08:09:51.218 SET FEATURES [Set transfer mode] Error 16 occurred at disk power-on lifetime: 1476 hours (61 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 f0 10 1a 40 04 Error: UNC at LBA = 0x04401a10 = 71309840 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 28 08 00 05 40 40 00 4d+08:09:46.229 READ FPDMA QUEUED 60 00 00 00 1a 40 40 00 4d+08:09:46.229 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 4d+08:09:46.227 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 4d+08:09:46.227 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 4d+08:09:46.225 IDENTIFY DEVICE Error 15 occurred at disk power-on lifetime: 1476 hours (61 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 b0 50 01 40 04 Error: UNC at LBA = 0x04400150 = 71303504 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 10 00 1a 40 40 00 4d+08:09:30.209 READ FPDMA QUEUED 60 28 08 00 05 40 40 00 4d+08:09:30.209 READ FPDMA QUEUED 60 00 00 00 01 40 40 00 4d+08:09:30.209 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 4d+08:09:30.209 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 4d+08:09:30.208 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 14 occurred at disk power-on lifetime: 1474 hours (61 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 18 48 24 c6 07 Error: UNC at LBA = 0x07c62448 = 130425928 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 18 30 48 24 c6 40 00 4d+06:01:06.848 READ FPDMA QUEUED 60 40 28 08 24 c6 40 00 4d+06:01:06.848 READ FPDMA QUEUED 60 10 00 d0 82 7a 40 00 4d+06:01:06.843 READ FPDMA QUEUED 60 08 20 68 f4 a1 40 00 4d+06:01:06.841 READ FPDMA QUEUED 60 00 18 00 00 6d 40 00 4d+06:01:06.841 READ FPDMA QUEUED Error 13 occurred at disk power-on lifetime: 1474 hours (61 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 78 c4 49 0d Error: UNC at LBA = 0x0d49c478 = 222938232 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 80 c3 49 40 00 4d+05:55:34.176 READ FPDMA QUEUED 60 00 08 80 c2 49 40 00 4d+05:55:33.816 READ FPDMA QUEUED 60 00 00 80 c1 49 40 00 4d+05:55:33.399 READ FPDMA QUEUED 60 00 08 80 c0 49 40 00 4d+05:55:33.213 READ FPDMA QUEUED 60 00 00 80 bf 49 40 00 4d+05:55:33.210 READ FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.